Engine Service

Bracket is used to hold a GM 1.5L engine Bracket is installed onto both camshafts, and holds the assembled hex on both cams to maintain t...

Counter-weighted design for high torque applications, including: Mercedes Benz (Can be used with CTA 3998 for Benz Applications) Nissan/Infinit...

Services Camshaft Adjuster (#10 Polydrive) bolts, where clearance is critical Bolts are found at the back of the engine-bay near the firewall 9mm ...

For '98 & earlier 2.5L 5 cyl. Volvos w/o CVVT Holds the camshaft in place during the timing belt replacement Made from 3/8" anodized alumin...

Special bars lock camshafts relative to each other during timing belt and tensioner service or when removing crank bolts Use with CTA #2872 TDC ...

Sockets are designed to install and remove Exhaust Gas Temperature sensors on cars & trucks without damaging connection wire, housing, sensor ...

Used to remove and install the intake manifold of a 2.0L 4V Turbocharged common rail TDI engine 10mm Triple Square (XZN) Ball End Applications:...

Designed to fit the flex plate teeth Insert the tool into the flywheel housing until it engages the ring gear Use with a 1/2" square drive tool (r...

1.5D Honda Head repair Inserts (5 Pc.) Longer thread inserts for maximum thread engagement Threads specifically designed for Honda, T...

Service head bolts on many VWs and Audis 1/2" square drive and 4-1/4" (10.7cm) OAL long for deep-reach applications Ribe wrenches will also servic...

Service head bolts on many VW & Audi models 1/2" square drive and 5-1/2" (14cm) long for deep-reach applications Ribe wrenches will also servi...

Use for install of wheel hub oil seal on single or dual wheel axle assemblies Seal installer adapter is driven with the 7" detachable handle Appli...

Installer is designed to eliminate lip-flare on the wear sleeve, which can cause oil leaks during install Properly installs the seal, which helps ...

Use to install and remove the camshaft adjusters Use to secure cam position during timing chain replacement Made from durable Cr-V hardened alloy ...

Use for aligning the camshaft timing angle to correct position Services Mercedes Benz (60°) V6 engine from 2011-2019 Compare to Mercedes Benz Fact...

Porsche Camshaft Tool Kit - 911 & 914/916. Porsche Camshaft Tool Kit includes: 3762 - Porsche Cam Turning Wrench - 911 & 914/916 - Porsch...

Porsche Camshaft Nut Wrench is used for loosening and tightening the camshaft nut The crowfoot design socket is a 46mm with a ½” square drive Appl...

Use for removing fuel injectors from BMW/MINI vehicles Services B38 (1.5L), B48(2.0L) & B58(3.0L) Engines Alignment plate and injector adapter...

Use for aligning the camshaft to TDC (Top Dead Center) Applications: 2014+ Mercedes Benz AMG C63, E63, S63, G63, GT and GT-S with biturbo 4.0L V8 ...

The timing tool set includes the tools required to properly service GM Atlas/Vortec engine family Kit includes: 7459 - GM Lower Timing Gear Retai...

Use for disassembly of counterbalance shaft gears Pressed on gear can only be removed with this tool Use with standard open-end 24mm hex wrench Se...

Drill Support + Drill 3.2mm

Sanding Papers Diameter 16mm (Set of 10)

Tap Support + Tap M4

Puller Support + Puller M3

17mm Offset Socket 3/8" Sq. Dr. Socket is included in kits 5083 & 8857

Lock Pin - Thin Compare to Ford Factory Tool 303-507 Applications Make Model Engine Years Ford Escape 2.3L DOHC 4V I4 2005-2012 Ford Fusio...

Lock Pin - Thick Compare to Ford Factory Tool 303-748 Applications Make Model Engine Years Ford Fiesta 1.25L Duratec 2005-2008 Ford Fiesta...

Use for aligning & holding the cams for timing chain service Pins insert into camshaft pulse plates and locks the cams in place ...

Holds camshaft in position during valve timing adjustment Services Porsche 996 Turbo Use in conjunction with CTA 3886 Compare to Porsche Factory T...

Tool kit is used to install the piston pin circlip on Porsche engines Includes:  5018X05 - Pin Driver & Extension 5018X06 - Alignment tool A...

Used for adjusting the camshafts when performing service on the timing system Also found in CTA No. 7066 Volvo Camshaft Alignment Kit Compare to V...

Vibration Damper Counter Holder for Porsche 970 & 92A Used to counter hold the crankshaft pulley during removal and installation Used for repl...

Tool mounts to the front of the block, its tabs engage both cam phasers to be held in place so the phaser bolts may be serviced The ECOTEC engines...

Tool kit is designed to service the engine timing system on Porsche 986, 987.1, 996, & 997.1 models The entire kit comes packed in a custom b...

Rotates camshaft for adjusting the engine timing or tightening the timing chain Applications: Audi A6, A7 & A8 equipped with the V8 4.0L TFS...