Suspension

"Double-D" socket holds shock piston stem while deep socket is used to remove the nut Internal dimensions: .33"(8mm) long x .25"(6mm) wi...

Tightens top mount nut with proper torque while holding the strut Includes: 82mm Deep Sockets sizes: 16, 17, 18, 19, 21, 22 & 24mm 4 Hex bi...

10 Point x 19mm socket services selected Honda & Acura rear trailing arms 1/2" Square drive Applications Applications include but are not lim...

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to ...

Special oval shaped bit end services Suspension Strut Housing Nuts found on mostly newer VW & Audi models After removing pinchb...

Removes and installs coil springs where removal through the center of the spring is not possible Services both Straight & Curved Coil Springs ...

Removes inner tie rods without removing outer tie rods Will service tie rods with flats and smooth tie rods Slide tool over end and tighten col...

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to remove wh...

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to remove wh...

Use to easily service ear style clamps on axle boots/hoses Clamps are often difficult to properly tighten and securer without the correct tool Too...

Removes the Pivot Pins found on both tilt and telescopic steering columns Works on GM, Ford, and Chryslers with Saginaw steering columns

For removal and fitting of shock absorbers without damaging the aluminum or cast iron knuckle Tool adjusts for centered or non-centered slot Ap...

Use with any Steering Wheel Puller, when steering wheels do not have tapped holes O.A.L.: 5" (127mm) Applications include: Cadillac Chevy...

Services most steering wheels, including telescopic tilt columns Includes: 4 sets of cap screws 2 yokes Metric & SAE lock plate adapters and ...

Separates the lower control arm ball joint from the steering knuckle Services 2005-2018 Ford, Lincoln & Mercury models (Not Limited Too) Extra...

This Drive Shaft Puller kit is designed for pulling drive shafts into hubs. Kit comes with six different size adapters: 5056X02...

41mm x 12 Point socket Applications include BMW & Mercedes lower ball joint Impact Quality Durable Design 1/2" Drive

Services the wide-style Inner CV Joint Assembly, found on Ford F150 4WD and other vehicles 63.5mm wide opening allows proper fitment wide applica...

Separates half-shafts from transaxle Shim tool is included to fill gaps on some applications Better and safer than hammer and bar Both are 14"...

Separates the ball joint from the spindle support arms found on many front wheel drive vehicles Adjusts up to 2" / 51mm for different size ball ...

Contains press, 3 receiver tubes, installation, and removal adapters, plus 4WD adapters to service '67 thru current 1/2 and 3/4 ton vehicles with ...

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to remove wh...

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to remove wh...

Includes components found in kit #7880 If you have discontinued kit #4080, purchase #7880X10 to upgrade your kit

A must for removing the steering wheel for the replacement or to repair the directional signal switch, horn contacts, etc. Will not damage steerin...

Includes: 3 sets of side bolts: 5/16"-18, 5/16"-24 and 3/8"-16 Yoke and center bolt with flat adapter Widest spread is 3 - 1/2"

Adapter flips to fit both 9/16" - 18 and 14mm threads to service tilt-wheel and telescoping columns Narrow yoke is 5" (127mm) deep

Used for installing a ball joint on a lower control arm Eliminates the need for an extra pair of hands Works with any 7/8” diameter p...

Designed to fit the slotted adjusting screw in tapered kingpins Application: Most Mack front axles (12,000 to 20,000 lbs.) Use with a ...

For the removal & installation of the front lower control arm bush(ing) Can be used in situations without removing the arm from the vehicle Wh...

Removes the front suspension ball joints quickly, safely and efficiently without damage 19mm (3/4") hexagon drive spindle can be turned with a w...

For E36 & E46 (3 Series only) Drive End: 16mm Hex This tool will not service some E36 with newer bushing style Threaded rod details: Length:...

Releases the Lower Ball Joint Services Audi A4 ('09 & up), A5 ('08 & up), A6 ('12 & up), A7 ('10 & up), Q5 ('09 & up) Allow...