Products

Includes jig to align camshafts during assembly Includes TDC pin to align the flywheel Services BMW M42, M44, M50, M52, M52TU, M54, M56, S50(US) &...

Used to set camshaft timing Includes 4 blocks & 2 locking fixtures for setting camshaft timing Engines: M60, M62 & M62TU Packed in blow-mo...

Properly aligns and locks camshaft in TDC position when adjusting or checking timing or replacing camshaft or timing chain on N62, N62TU & N73...

All the tools needed to service '09 & up models with turbo engines - TFSI Includes crank counter hold tool, crankshaft thrust piece, (4) drift...

Services BMW: M21, M40, M41, M42, M43, M43TU, M44, M47, M47TU, M50, M51, M52, M52TU, M54, M56, M57, M57TU, M60, M62, M62TU, M70, M73, S50B30, S50B...

Timing tool set for BMW N63 & S63 V8 engines Includes necessary alignment fixtures Components: 2893X01 - TDC Lock Pin 2893X02 - Alignment Bar...

Loosens central crankshaft bolt on N63 & S63 engines Part of kit #2893 Services various 2008-2013 BMW Instructions Removal: Remove the engin...

For servicing engine timing on the M60 & M62 Engines Components 2894X01 - 2-pin socket 2894X02 - L-shaped locking pin 2894X03 - Locking fi...

Adjusts VANOS to far left stop when adjusting valve timing or assembling 2 pin design with hex drive Use with CTA 2894 - BMW Timing Tool Kit

For servicing engine timing on the M52, M54 & M56 Engines Includes: 2895x01 Vanos Bracket 2895x02 Spocket Alignment Plate 2895x03 ...

Use when installing camshafts or cylinder heads Applications include: 1999 - 2005 BMW M52TU, M54 & M56 with twin vanos Part of #289...

For servicing engine timing on the S65 Engine Aligns and fixes the camshaft at Top Dead Center (TDC) during assembly Also used to hold the cranksh...

Upgrade for CTA Kit #2886 For BMW N55 Comparable to BMW #3028, #110300, #114280, #114285, #114290 and #118520. Applications ...

Opens stuck grease fittings and grease joints with powerful hydraulic impact Softens dried-out grease inside joints and allows one to grease neg...

Saves the memory of the on-board vehicle computer when the battery is disconnected Plugs into cigarette lighter Use with 9V alkaline b...

Allows one person to start or crank engine while under the hood or from either side of the vehicle Soft, non-slip rubber grip features a high curr...

Tests for the presence of spark without risk of shock and without damaging wires Identifies badly fouled spark plugs Includes 48" (122cm) lead, ho...

Quickly and safely troubleshoots no-starts See and hear if spark is present, test intensity or test spark timing with conventional ignition INSTR...

Tests high voltage in spark plugs, plug wires and distributor caps Test 6 & 12 volt systems for shorts, grounds and open circuits with power...

For 6 & 12 volt systems Features heavy duty ground clip and insulator 5' / 1.5m rubber wire with spring supported strain relief and extra th...

Tests for shorts, grounds, open circuits, broken wires and bad connections in 6 & 12 volt systems Features 42" / 107cm long wire, impa...

Two 36" (91cm) jumper leads of 16 gauge stranded wire in heavy insulation for all-purpose applications MADE IN USA WARNING: This product can ...

High impedance tester protects computer circuitry, drawing less than 7 milliamps Dual color LED indicates red for power (high) and green for groun...

2 Pc. VW Roof Grab Release Tool Kit Includes: 1464 - Used to remove the roof grab handle of new VW models. Without causing damage to clips or hea...

Use for timing service on BMW, MINI & Toyota (Supra) B38, B48 & B58 engine variants Locking camshafts and crankshaft, adjusting the camsha...

12-Point Triple-Square "XZN" Sockets Service fasteners on VW, Audi, Porsche, BMW, Volvo, Mercedes-Benz and some Detroit Diesel engines 2-piece des...

DISCONTINUED: SUPERSEDED BY #7510 Go Through Deep Hex Socket - 16mm

DISCONTINUED: SUPERSEDED BY #7511 Go Through Deep Hex Socket - 17mm

DISCONTINUED: SUPERSEDED BY #7512 Go Through Deep Hex Socket - 18mm

Go Through Deep Hex Socket - 19mm

*** DISCONTINUED & REPLACED BY CTA #7521 *** Go Through Deep Hex Socket - 21mm

Go Through Deep Hex Socket - 22mm

Sliding "T" Bar - 1/2" Drive

6mm Hex Bit x 1/2" Sq Drive

7mm Hex Bit x 1/2" Sq Drive