Black Friday

Applications: Ford F150 & Bronco with Dana 44 outer locking nut (1981-1997) 1/2" square drive Dimensions: OAL: ...

For 6 & 12 volt systems Features heavy duty ground clip and insulator 5' / 1.5m rubber wire with spring supported strain relief and extra th...

Set of three (3) stones, with cotter pins Use with CTA#2310 Length: 4" / 102mm Grit: Medium - 220 MADE IN USA

Resurface cylinder walls so new rings will seat Eliminate minor cylinder wall imperfections Adjustable diameter and tension settings Flex shaft wi...

Fine Grit (400) Qty: 3 Length: 22mm Includes cotter pins Will also fit other brands! MADE IN USA

Quickly and easily install stretch belts found on many late model vehicles These drive systems do not have a tensioner and require the proper inst...

High-torque 2-piece bit socket design 1/2" Square Drive Size:19mm MADE IN USA

Use for holding the crankshaft for service Services: B38 (1.2L & 1.5L), B48 (2.0L) & B58 (3.0L) engines, 2015+ Application: BMW 340i, 440i...

2 Pc set includes filp socket and 3" extension Services 27mm lug nuts or Lug Bolts with missing and distorted chrome caps, found on Land Rover &...

Services 27mm lug nuts or Lug Bolts with missing and distorted chrome caps, found on Land Rover & More Chrome capped lug nuts can eas...

Comprehensive kit includes required components to perform complete timing service Services Porsche 911 Turbo & GT2 996 (1997-2006) & 997.1...

Holds the engine when replacing the timing belt Aligning the camshaft and crankshaft position Services vehicles with the "VEA" 2.0L turbocharged a...

3 flat tab design w/ protruding inner cylinder for perfect seal Use with CTA 7015 Brake Bleeding Tank Internal Male Insert O.D. = 30.15mm I.D. = 4...

Extracts broken dipstick tubes, a common issue on Dodge 5.7L & 6.1L HEMI Engines during engine service When the dipstick tube breaks off, a pi...

Holds intake camshaft sprocket during timing service Services Porsche 911 Turbo (996) OAL: 25cm/250mm (9.85") Compare to Porsche Factory Tool 9653...

#9 Ribe/Poli-drive (10mm) Service most VW & Audi headbolts 150mm long wrenches Use with 1/2" square drive tools Made i...

Kit includes: #3472 Benz Injector Remover. T-bar/Slide hammer designed for easier removal of the injector nozzle. #2213 Mercedes Benz Injector ...

Easily setup and service the Mercedes Benz M156 engine timing while installed A properly working timing system allows the engine’s valves to ope...

Tool kit is used to setup and service the engine timing on Porsche 4.8L V8, 3.0L Supercharged V6 & 3.6L V6 A properly working timing system al...

Used when assembling crankshaft PTFE seal & flywheel end Provides proper installation of rear main seal For 2008 - 2017 vehicles with TSI engi...

Used for replacement of actuator with position sender for charge pressure actuator Use on 2.0L Diesel Common Rail engine Compare to VW/Audi Factor...

For installing the seals on Mercedes Benz & Infiniti fuel injectors Services: M133, M152, M157, M274, M276 & M278 engines Compare to Merce...

Services Volvo 850, 940, 940SE, 960, S60, S70, S80, V70, V70XC, XC70 & XC90 Compare to Volvo Factory tool #9995371 Because threads are very fi...

Specially designed to position the camshafts in TDC position Slackens and tightens the bolts attached to the camshaft gears Compare to Mercedes Be...

DISCONTINUED - SUPERCEDED BY 4031M Safest, strongest tool for lock ring service Hold single handle then adjust screw mechanism to control forged j...

Use with CTA #7400 Standard ATF Filling Tank connector end with 200mm / 8" clear hose OD: 8mm ID: 5mm Will work on most "Non-CTA" ATF...

Services belts on Volvo & BMW Heavy-duty long bar with T60 Torx Bit on one end & T50 Torx Bit on other end, plus 16mm x 12-point opening b...

Press tool removes and installs control arm bushings without having to remove the control arm from the car See application chart for compatible ve...

Alloy steel tap to clean Oil Pan & other threads Size: 12mm x 1.75 Applications: Ford, GM, GMC, Saturn

4" / 102mm long for deep-reach applications 2-piece construction for high torque applications 3/8" drive Size: 7mm MADE IN USA

4" / 102mm long for deep-reach applications 2-piece construction for high torque applications 3/8" drive Size: 5mm MADE IN USA

15" flex hose allows access to all cylinders Side release valve permits multiple readings without removing tester Includes quick disconnect couple...

15" flex hose allows access to all cylinders Side release valve permits multiple readings without removing tester Includes 14 & 18mm spark plu...

Includes 2-1/2" (65mm) diameter with dual calibration (0-300 PSI / 0-21kg/cm²) 6' / 1.8m hose and SAE & Metric adapters ATTENTION - If ga...

To be used with CTA kit # 98141 Includes a set of five (5) - 3/4" inserts Thread Pitch: 1.25 (Metric)

To Test Pressure Relief Valve in Cooling System Cap All metal construction with 48mm x 4mm Buttress Threads Use with CTA #7050 Pressure Tester Co...