Timing Tools

Bracket is used to hold a GM 1.5L engine Bracket is installed onto both camshafts, and holds the assembled hex on both cams to maintain t...

Counter-weighted design for high torque applications, including: Mercedes Benz (Can be used with CTA 3998 for Benz Applications) Nissan/Infinit...

Services Camshaft Adjuster (#10 Polydrive) bolts, where clearance is critical Bolts are found at the back of the engine-bay near the firewall 9mm ...

For '98 & earlier 2.5L 5 cyl. Volvos w/o CVVT Holds the camshaft in place during the timing belt replacement Made from 3/8" anodized alumin...

Special bars lock camshafts relative to each other during timing belt and tensioner service or when removing crank bolts Use with CTA #2872 TDC ...

Use to install and remove the camshaft adjusters Use to secure cam position during timing chain replacement Made from durable Cr-V hardened alloy ...

Use for aligning the camshaft timing angle to correct position Services Mercedes Benz (60°) V6 engine from 2011-2019 Compare to Mercedes Benz Fact...

Porsche Camshaft Tool Kit - 911 & 914/916. Porsche Camshaft Tool Kit includes: 3762 - Porsche Cam Turning Wrench - 911 & 914/916 - Porsch...

The timing tool set includes the tools required to properly service GM Atlas/Vortec engine family Kit includes: 7459 - GM Lower Timing Gear Retai...

Use for disassembly of counterbalance shaft gears Pressed on gear can only be removed with this tool Use with standard open-end 24mm hex wrench Se...

Lock Pin - Thin Compare to Ford Factory Tool 303-507 Applications Make Model Engine Years Ford Escape 2.3L DOHC 4V I4 2005-2012 Ford Fusio...

Lock Pin - Thick Compare to Ford Factory Tool 303-748 Applications Make Model Engine Years Ford Fiesta 1.25L Duratec 2005-2008 Ford Fiesta...

Use for aligning & holding the cams for timing chain service Pins insert into camshaft pulse plates and locks the cams in place ...

Holds camshaft in position during valve timing adjustment Services Porsche 996 Turbo Use in conjunction with CTA 3886 Compare to Porsche Factory T...

Tool kit is used to install the piston pin circlip on Porsche engines Includes:  5018X05 - Pin Driver & Extension 5018X06 - Alignment tool A...

Used for adjusting the camshafts when performing service on the timing system Also found in CTA No. 7066 Volvo Camshaft Alignment Kit Compare to V...

Tool mounts to the front of the block, its tabs engage both cam phasers to be held in place so the phaser bolts may be serviced The ECOTEC engines...

Tool kit is designed to service the engine timing system on Porsche 986, 987.1, 996, & 997.1 models The entire kit comes packed in a custom b...

Rotates camshaft for adjusting the engine timing or tightening the timing chain Applications: Audi A6, A7 & A8 equipped with the V8 4.0L TFS...

Used for aligning the position of the camshaft pulley T100 x 1/2"Dr. Made of Durable, high quality Carbon Steel Compare to Mercedes Benz Factory T...

For servicing the Camshafts and the Timing Chain during Installation & Removal on Mercedes Benz (3.0L CDi Diesel engine) Included in kit: ...

Crankshaft socket slips over crank snout Enables engine builder to rotate a complete engine with any 1/2" ratchet or breaker bar Designed to allow...

A must for removing and installing serpentine belts with spring-loaded idler pulleys 23” long slender design provides proper reach and prevents ...

Kit combines CTA: 1068 - Crank Bolt Socket - 27mm Use for easily breaking loose crank bolts Counter-weighted design for high torque application...

Vibration Damper Counter Holder for Porsche 970 & 92A Used to counter hold the crankshaft pulley during removal and installation Used for repl...

Set of three wedges designed to hold/wedge while performing timing service Use on Sigma platform engines, 1.4L & 1.6L Duratec 16V engines from...

Fits into the idler pulley and turns it to release tension for replacement of the serpentine belt 3/4" square head Applications 850 (1993-1997)...

Includes Two long-handled (22" / 55cm) wrenches, each with special bends, designed specifically for Mini Coopers equipped with the N12, N14, N16 a...

Used for installing serpentine belts for A/C compressors on N62 engines which are not equipped with automatic belt tensioners Some N62 powered car...

All the tools needed to service '09 & up models with turbo engines - TFSI Includes crank counter hold tool, crankshaft thrust piece, (4) drift...

Includes jig to align camshafts during assembly Includes TDC pin to align the flywheel Services BMW M42, M44, M50, M52, M52TU, M54, M56, S50(US) &...

Toyota Timing Belt Tensioner Compressor Allows for easy belt replacement For 95 & Up T100, Tacoma & 4 Runner trucks Internal nut to ex...

For locking and positioning camshafts, crankshafts & injection pump sprockets when replacing timing belts or chains Includes setting gauge and...

Extra-long (26" / 66cm) handled tool with special jaws relieves tension on belt tensioner for poly-ribbed belt service Services: ...

Special bars lock camshafts relative to each other during timing belt and tensioner service or when removing crank bolts Use with CTA #2872 TDC ...