Suspension

Utilize this tool to extract the splined axle end from the wheel flange or hub of rear-wheel drive and front-wheel drive 4-LUG Euro applications C...

Contains press, 3 receiver tubes, installation, and removal adapters, plus 4WD adapters to service '67 thru current 1/2 and 3/4 ton vehicles with ...

Removes damaged wheel studs and inner Budd nuts Internal tapered reverse threads lock onto damaged stud or nut and easily pulls off using impact w...

The BMW AWD Transfer Case Bushing Tool contains the necessary components for removal and installation of transfer case mount bushings on BMW AWD m...

Comprehensive tool kit allows for the removal and reinstallation of the transfer case mount Includes adapters and other components needed for the ...

Medium Jaw for 8200 Strut Lifter Tool Services average diameter struts Included with 8200 tool #8200X02 - Medium Jaw (Range: 40-62mm)

Master kit services Rear Wheel Hubs & Bearings on European vehicles, plus Front Wheel Hubs & Bearings on US, Asian & European vehicles...

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to remove wh...

Includes components found in kit #7880 If you have discontinued kit #4080, purchase #7880X10 to upgrade your kit

Includes: 3 sets of side bolts: 5/16"-18, 5/16"-24 and 3/8"-16 Yoke and center bolt with flat adapter Widest spread is 3 - 1/2"

Adapter flips to fit both 9/16" - 18 and 14mm threads to service tilt-wheel and telescoping columns Narrow yoke is 5" (127mm) deep

Designed to fit the slotted adjusting screw in tapered kingpins Application: Most Mack front axles (12,000 to 20,000 lbs.) Use with a ...

For E36 & E46 (3 Series only) Drive End: 16mm Hex This tool will not service some E36 with newer bushing style Threaded rod details: Length:...

Allows replacement of the rear axle carrier balljoint with the carrier in place Services: E38, E39, E52, E53, E60, E61, E63, E64, E65, E66, R53 BM...

Use to remove and install the front lower control arm and torque strut bushings Services: Mercedes W203, 204, 209, 211, 215, 220, 221 and 230 ch...

Ball joint press tool is used to install the ball joints into the steering knuckles of your P2 chassis Volvo models Includes 4 slide hammer pulle...

Use for removing and installing the top shock retaining nut on 850, S40, C70, S60, S70, S80, V70, XC70 & XC90 models Includes holding socket a...

Separates ball joints from the steering knuckle making replacement and disassembly of front suspensions easy Prevents damage to suspension...

Swivel tipped forcing screw aligns to the tie rod stud to prevent damage Heavy-duty forged body Services imports and many FWD vehicles, includi...

Separates tie rod ends from steering knuckles, idler arm and Pitman arms Prevents damage to steering components OAL: 16" (40cm)

Pulls CV joints with hidden retaining rings without damaging the roller bearing inside the joint Use with CTA #4310 Axle Puller 5/8" - 18 thr...

Set of free-end clamps for banding CV Joint Boots Use with #4230 Banding Tool Includes two 10" / 25cm & two 19" / 48cm clamps for any CV J...

Installs free-end clamps CTA #4240 - CV Joint Boot Clamp Set - or pre-formed clamps on CV Joint Boots Operate with 1/2" hex drive or T-handle

Compresses the coil spring to replace the shock absorber unit or spring Works on bent struts, strut tubes, and damaged pieces Forged constructions...

Removes the putman arm from most vehicles Center screw with pointed tip and 3/4" hex head Opening: 1-5/16" / 33mm Depth: 2-1/2 ...

Remove and install screw-in type ball joints 3/4" drive Size: 2-9/64" Applications: Light trucks and vans

Remove and install screw-in type ball joints 3/4" drive Size: 1-59/64" Applications: Mid-size, rear-wheel drive cars