Suspension

Services rear axle hub bearing retaining nut on heavy duty RAM trucks Services rear hubs with 12 pins on RAM 2019+ 3500, 4500, 5500 (D2, DD, DP) C...

This tool is designed to remove and install the hub nut on these axles, which is critical to maintaining the proper preload on the axle components...

Special oval shaped bit end services Suspension Strut Housing Nuts found on mostly newer VW & Audi models After removing pinchb...

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to remove wh...

Separates the lower control arm ball joint from the steering knuckle Services 2005-2018 Ford, Lincoln & Mercury models (Not Limited Too) Extra...

Removes inner tie rods without removing outer tie rods Will service tie rods with flats and smooth tie rods Slide tool over end and tighten col...

Services removal and installation of struts, drive shaft, control arms and ball joint hub separation on vehicles with double wishbone suspension ...

For removal and fitting of shock absorbers without damaging the aluminum or cast iron knuckle Tool adjusts for centered or non-centered slot Ap...

Removes and installs coil springs where removal through the center of the spring is not possible Services both Straight & Curved Coil Springs ...

Separates the ball joint from the spindle support arms found on many front wheel drive vehicles Adjusts up to 2" / 51mm for different size ball ...

14mm x 12-point XZN socket with tamper-proof head services various '03 & up VW, Audi, and Porsche Axle Bolts, Differential Bolts, and Transmi...

Large Jaw for 8200 Strut Lifter Tool Services larger diameter struts Optional for 8200 tool

Small Jaw for 8200 Strut Lifter Tool Services smaller diameter struts Optional for 8200 tool

Master kit services Rear Wheel Hubs & Bearings on European vehicles, plus Front Wheel Hubs & Bearings on US, Asian & European vehicles...

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to remove wh...

Use to easily service ear style clamps on axle boots/hoses Clamps are often difficult to properly tighten and securer without the correct tool Too...

Removes & installs cylinder end stopper on '04 - '09 Lexus RX330 & RX350, plus '04 - '07 Toyota Highlander Allows steering rack to remai...

Removes the Pivot Pins found on both tilt and telescopic steering columns Works on GM, Ford, and Chryslers with Saginaw steering columns

Services most steering wheels, including telescopic tilt columns Includes: 4 sets of cap screws 2 yokes Metric & SAE lock plate adapters and ...

Removes the front suspension ball joints quickly, safely and efficiently without damage 19mm (3/4") hexagon drive spindle can be turned with a w...

Removes and installs the top shock retaining nut on W203 body Mercedes vehicles 2-pin design with 22mm hex body Applications ...

Press tool removes and installs control arm bushings without having to remove the control arm from the car See application chart for compatible ve...

Holds torsion bar while making adjustments Services: '88 - '10 GMC Chevrolet 1/2 ton, 3/4 ton and 1 ton pickups S-10 Blazer S-15 Jimmy 4WD pickup...

Separates half-shafts from transaxle Shim tool is included to fill gaps on some applications Better and safer than hammer and bar Both are 14"...

Removes, installs, and compresses coil springs that can be reached through the center of the coil Features Acme threaded rod and forged, h...

Contains press, 3 receiver tubes, installation, and removal adapters, plus 4WD adapters to service '67 thru current 1/2 and 3/4 ton vehicles with ...

The BMW AWD Transfer Case Bushing Tool contains the necessary components for removal and installation of transfer case mount bushings on BMW AWD m...

Comprehensive tool kit allows for the removal and reinstallation of the transfer case mount Includes adapters and other components needed for the ...

Use for removing and installing ball joint lock nut on classic Porsche models Services: 911 (1969-1989), 912 (1969-1989), 914 (1970-1976) & 93...

Medium Jaw for 8200 Strut Lifter Tool Services average diameter struts Included with 8200 tool

Master kit services Rear Wheel Hubs & Bearings on European vehicles, plus Front Wheel Hubs & Bearings on US, Asian & European vehicles...

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to remove wh...

Includes components found in kit #7880 If you have discontinued kit #4080, purchase #7880X10 to upgrade your kit

Includes: 3 sets of side bolts: 5/16"-18, 5/16"-24 and 3/8"-16 Yoke and center bolt with flat adapter Widest spread is 3 - 1/2"