Engine Service

Use for removing fuel injectors from BMW/MINI vehicles Services B38 (1.5L), B48(2.0L) & B58(3.0L) Engines Alignment plate and injector adapter...

The timing tool set includes the tools required to properly service GM Atlas/Vortec engine family Kit includes: 7459 - GM Lower Timing Gear Retai...

Use to install the crankshaft rear oil seal and wear sleeve. Services 2003-2010 Ford 4.5L, 6.0L & 6.4L Power Stroke engines Applications: Ford...

14mm Offset Socket 3/8" Sq. Dr. Socket is included in kits 5083 & 8857

Tool kit is used to install the piston pin circlip on Porsche engines Includes:  5018X05 - Pin Driver & Extension 5018X06 - Alignment tool A...

Vibration Damper Counter Holder for Porsche 970 & 92A Used to counter hold the crankshaft pulley during removal and installation Used for repl...

Comprehensive tool kit services Ford, Lincoln, Land Rover & Mazda 1.4L, 1.5L, 1.6L, 2.0L, 2.3L, 2.5L & 3.0L engines Used on EcoBoost, Dura...

Tool mounts to the front of the block, its tabs engage both cam phasers to be held in place so the phaser bolts may be serviced The ECOTEC engines...

Used for aligning the position of the camshaft pulley T100 x 1/2"Dr. Made of Durable, high quality Carbon Steel Compare to Mercedes Benz Factory T...

For repairing the balancer shaft, holding chain sprocket and for removing and installing the oil pump, chain, and sprocket for repair This kit in...

Used to counter-hold the crankshaft pulley to release and tighten center bolt Compare to Volvo Factory Tool: #999 5433 Application Details ...

Kit combines CTA: 1068 - Crank Bolt Socket - 27mm Use for easily breaking loose crank bolts Counter-weighted design for high torque application...

Counter-weighted design for high torque applications, including: Mercedes Benz (Can be used with CTA 3998 for Benz Applications) Nissan/Infinit...

Services Camshaft Adjuster (#10 Polydrive) bolts, where clearance is critical Bolts are found at the back of the engine-bay near the firewall 9mm ...

This wrench is designed for servicing the timing belt Use for installation on 2.2L & 2.5L liter I4 In-Line 4 engines Features special 7-point ...

Includes Two long-handled (22" / 55cm) wrenches, each with special bends, designed specifically for Mini Coopers equipped with the N12, N14, N16 a...

For '98 & earlier 2.5L 5 cyl. Volvos w/o CVVT Holds the camshaft in place during the timing belt replacement Made from 3/8" anodized metal pla...

For VAG 1.9L & 2.0L TDI PD DOHC Engines found on Audi A4, A6, VW Golf, Jetta and Touareg Models Includes: 2 Crankshaft Holders and complete se...

For locking and positioning camshafts, crankshafts & injection pump sprockets when replacing timing belts or chains Includes setting gauge and...

Special bars lock camshafts relative to each other during timing belt and tensioner service or when removing crank bolts Use with CTA #2872 TDC ...

Removes harmonic balancers without tapped holes Services V6 & V8: GM (5.3L, 5.7L 6.0L, 6.2L & 7.0L) Chrysler, Dodge & Jeep (3.5L, 3.7...

Sockets are designed to install and remove Exhaust Gas Temperature sensors on cars & trucks without damaging connection wire, housing, sensor ...

Includes one Fan clutch Wrench: 36mm & Holding Tool: 40mm Services most Mercedes models from Mid-90's and up Also services: Land Rover (Disco...

Locks the flywheel while the transmission is removed for service Applications are M47TU, M54, M57T2, M57TU, N40, N42, N43, N54, N45T, N46, N46T, N...

Holds Harmonic Balancer in place when removing or installing center bolt of Ford Taurus Pulley Extension Tool can be used to turn the engine to ga...

For replacing fuel filter or servicing the water sensor without damage Services '01 - '11 6.6L Duramax diesel engines (Aftermarket) 6-...

8mm 12-point double hex bit with integrated 1/2" square drive holder Designed for use on Toyota, Lexus, and Scion vehicles up to model year 2006 B...

Installs front crankshaft oil seal and wear sleeve to repair grooved crankshaft surfaces Ensures proper depth and alignment during seal and sleeve...

Designed for precise service of Jeep 2.0L turbocharged (2.0T) engines, this set allows accurate alignment of the camshaft and proper control of ch...

Adapter plate provides threaded anchor points on the front timing chain cover for secure bolt installation            Allows for even separation ...

Fits older 15mm turbocharger bolts on Cummins ISB 5.9L and 6.7L Turbo Diesel Engines 15mm 12-point wrench 1/2" drive Ideal for cleaning and servic...

Replaces Teflon fuel injector seals on Hitachi, Bosch, Continental, and Delphi injectors Services: Ford EcoBoost, GM (2010+) & Subaru Turbo di...

Installs both the front seal and the damper Services F-250, F-350, F-450 & F-550 Super Duty 7.3L (Powerstroke & T444E) engine ...

The Ford crankshaft damper holding tool, part number 6150, is designed for holding the crankshaft damper in place during servicing of 2012 and new...

Locks crankshaft and camshafts in place to set and hold precise engine timing Allows proper camshaft and pulley torquing without losing set positi...