Engine Service

Adjusts timing belts that have idler pulleys with pin holes Pins in offset head of tool engage the pulley to rotate around the retaining bolt D...

Adjustable handle position allows the tension to be applied directly to the idler roller even with limited access Pins on tool engage the offset...

6 tools for belt tensioning or adjusting Includes: Open Stock 2766: Short Wrench 2767: Long Wrench/Short Offset 2768: Long Wrench/Long Offset 276...

Use to remove and install Fan Clutch Assemblies when replacing Water Pumps or doing other Engine Services Use two wrenches together: one for h...

Use to remove and install Fan Clutch Assemblies when replacing Water Pumps or doing other Engine Services Size: 36 x 48mm ( 17/8" x 17/16" ) Appli...

Removes springs and valve guide seals without removing cylinder head. Used by removing rocker and fastening tool to stud with nut, then use an a...

Application: Tractors/Diesel Trucks Depth: 6" (150mm) Range: 60 - 175mm Features ratchet mechanism with square drive tools to a...

Use for turning the flywheel crank on Paccar engines Services 2011-2016 Kenworth and Peterbilt T880 models with Paccar MX, MX PMCI-2, MX-...

10mm Triple-Square "XZN" 12-Point Service most VW & Audi headbolts 150mm long wrenches Use with 1/2" square drive tools Ma...

Applications: Mack E7 and Cat 3208 Dimensions: 8 Splines x 1.725”(43.815mm) Compare to Factory Tool #0508477 1/2" Square Drive Application Detail...

Tool is used for Compressing valve springs on the 3.0L without having to remove the head Applications: Fusion, Milan, MKZ, Escape, Mariner, Five H...

Primarily services Ford 4.0L SOHC V6's And some late model 4.6L V8's 3 pieces with detachable end to enable access in tight areas Compare to Ford ...

Designed for BMW cylinder head bolts 1/2" square drive bits are extra long (OAL 200mm) Allows access to reach down and remove stubborn cylinder he...

Designed for Honda, some Toyota's, etc. (Modifications may be required for applications other than Honda) Thread inserts are longer for maximum en...

Removes stubborn pins from cylinder head 85mm OAL for access in tight areas where slide hammers wont fit Services Benz M102, M110, M115, M116, M11...

Holds Harmonic Balancer in place when removing or installing center bolt of Ford Taurus Pulley Extension Tool can be used to turn the engine to ga...

Counter-weighted design for high torque applications OAL: 89mm Use with 1/2" square drive tools Includes 3 metric sizes: 1064 - 17mm - Honda, ...

Installs Oil Rail Ball Tubes in Oil Manifolds found on 2004.5 - 2007 Powerstroke 6.0L engines Also works as alignment tool Size: 22.75mm hex w...

Removes valve stem seals from overhead camshaft engines Special designed long reach jaws (3-14/" / 80mm) access recessed valves on 4 valve per c...

27mm socket with window Services injectors found on BMW, Ford, Fiat, Nissan, VW, Mercedes Benz, etc. Black finish with 1/2" square drive

Fits cylinder head bolts on BMW M42 and M50 engines 1/2" square drive with 6" (15cm) shaft Applications Manufactur...

Use with 3/4" drive tools to transmit high toque needed to losen and tighten head bolts Allows access to rear head bolts by eliminating t...

2 Pc. Set: 2450x03 - size: .001-.003" (green) 2450x04 - size: .002-.006" (red) Measures clearances of engine rod and main bearings without expe...

The offset jaws will grip the valve spring in parallel compression with no need to remove the head. The jaws are extra long for use on high perf...

Use with the cylinder head still on the engine and in the car, or with the cylinder head removed Tool bolts to the head while the lever pivots fro...

Removes valve spring keepers and springs without removing the cylinder head Adjusts to fit springs on most cars Sliding "T" handle for close clear...

Designed to work in areas of difficult access using direct action compressor lever for better visibility Includes 2 valve spring adapter, fittin...

Removes and replaces valve keepers on all gas and diesel overhead valve engines, including motorcycle, marine and aircraft engines Tool is spring-...

Hardened steel tips allow for easy seal removal OAL: 10" (25cm)

For fast overhead valve repairs without removing cylinder head Fit 14 & 18mm spark plug holes Accepts 1/4" air hose coupling

Primes the lubricating system of new and rebuilt engines, sending oil to the internal moving parts before the first start Use with 3/8" o...

Primes the lubricating system of new and rebuilt engines, sending oil to the internal moving parts before the first start Use with 3/8" o...

Primes the lubricating system of new and rebuilt engines, sending oil to the internal moving parts before the first start Use with 3/8" o...

SUPERSEDED BY CTA #4021 - Piston Ring Compressor 3" Application: Passenger Cars Depth: 31/2" (89mm) Range: 21/8 - 5" (54 - 127mm) Features ratchet...

Holds the crankshaft while tightening the crank bolt Application Details Make Engine Year Lexus 3.0L L6 1990+ Lexus 3.0L V6 1990+ L...

Two part splined wrench is required for removal and replacement of free-wheel drive pulleys found on Bosch Alternators 10mm x 12 point end locks a...