Engine Service

Locks the flywheel while the transmission is removed for service Applications are M47TU, M54, M57T2, M57TU, N40, N42, N43, N54, N45T, N46, N46T, N...

Designed for Honda, some Toyota's, etc. (Modifications may be required for applications other than Honda) Thread inserts are longer for maximum en...

Services Volvo 850, 940, 940SE, 960, S60, S70, S80, V70, V70XC, XC70 & XC90 Compare to Volvo Factory tool #9995371 Because threads are very fi...

Removes stubborn pins from cylinder head 85mm OAL for access in tight areas where slide hammers wont fit Services Benz M102, M110, M115, M116, M11...

Valve spring compressor for Jeep, Dodge & Chrysler 3.7L & 4.7L engines Services DR, HB, KA, KJ, KK & ND systems 3/8" drive Applicatio...

Holds Harmonic Balancer in place when removing or installing center bolt of Ford Taurus Pulley Extension Tool can be used to turn the engine to ga...

Counter-weighted design for high torque applications OAL: 89mm Use with 1/2" square drive tools Includes 3 metric sizes: 1064 - 17mm - Honda, ...

Installs Oil Rail Ball Tubes in Oil Manifolds found on 2004.5 - 2007 Powerstroke 6.0L engines Also works as alignment tool Size: 22.75mm hex w...

Use to remove and install the snap-ring on the long reverse piston and return spring, without removing the center shaft and clutch assembly from t...

150mm long T55 Torx® wrench Services many Mercedes, including 1998-2005 M112/M113, plus 2007 2.4L Dodge Caliber w/New World Engine, see below fo...

27mm socket with window Services injectors found on BMW, Ford, Fiat, Nissan, VW, Mercedes Benz, etc. Black finish with 1/2" square drive

Fits cylinder head bolts on BMW M42 and M50 engines 1/2" square drive with 6" (15cm) shaft Applications Manufactur...

Use with 3/4" drive tools to transmit high toque needed to losen and tighten head bolts Allows access to rear head bolts by eliminating t...

Service head bolts on many VWs and Audis 1/2" square drive and 4-1/4" (10.7cm) long for deep-reach applications Ribe wrenches will also service...

2 Pc. Set: 2450x03 - size: .001-.003" (green) 2450x04 - size: .002-.006" (red) Measures clearances of engine rod and main bearings without expe...

The offset jaws will grip the valve spring in parallel compression with no need to remove the head. The jaws are extra long for use on high perf...

Use with the cylinder head still on the engine and in the car, or with the cylinder head removed Tool bolts to the head while the lever pivots fro...

Removes valve spring keepers and springs without removing the cylinder head Adjusts to fit springs on most cars Sliding "T" handle for close clear...

Designed to work in areas of difficult access using direct action compressor lever for better visibility Includes 2 valve spring adapter, fittin...

Removes and replaces valve keepers on all gas and diesel overhead valve engines, including motorcycle, marine and aircraft engines Tool is spring-...

Hardened steel tips allow for easy seal removal OAL: 10" (25cm)

For fast overhead valve repairs without removing cylinder head Fit 14 & 18mm spark plug holes Accepts 1/4" air hose coupling

Installs and removes piston rings without damaging Spring loaded Range: 2-1/2 - 6-1/4" (64 - 159mm)

Holds the crankshaft while tightening the crank bolt Application Details Make Engine Year Lexus 3.0L L6 1990+ Lexus 3.0L V6 1990+ L...

Installs harmonic balancer or drive pulleys that are pressed on the camshaft Includes 12 adapters: M16-2.0 M16-1.5 M14-2.0 M14- 1.5 M12-1.75 M12-...

Used to install Harmonic Balancers on V8s and V6s on '04 - current Ford*, '08 - current GM**, & '06-current Chrysler/Dodge*** Reduces risk of...

Two part splined wrench is required for removal and replacement of free-wheel drive pulleys found on Bosch Alternators 10mm x 12 point end locks a...

Removes corrosion and straightens damaged threads in Oxygen Sensor holes M18 x 1.5 size can also be used on same size Spark Plug threads Use wi...

17mm hex with 3/8” square drive. Fits all Gems engine Land Rovers, including: Range Rover Classic - ’87 – ’95 Range Rover 4.0/4.6 - ’95 – ’98 Dis...

7/8” (22mm) hex socket with narrow slot for extra strength Combination 3/8" square drive & 1" hex drive Nickel plated

Stubby crowfoot design with deeper socket 7/8” (22mm) hex with double 1/2” square drive 60mm long x 48mm high

Universal slotted socket will service all 7/8” (22mm) hex vacuum switches and oxygen sensors Use with 3/8” square drive tools or 7/8” (22mm) wre...