Engine Service

Mercedes Benz 36mm Fan Clutch Wrench Ford & GM vehicles with a 36mm fan clutch nut Land Rover (Discovery 2) Services most models from mid-9...

Mercedes Benz 40mm Holding Tool Services most models from mid-90's and up High Polish Finish

For adjusting camshaft position during cylinder head reassembly or setting injection pump Works on VW Diesel with ALH engines Plus Audi diesel ...

  Locks and holds camshafts when adjusting the left and right camshafts Services: Audi A4, A6 & A8 (2001 – 2008) with AVK engine Includes hold...

Holds the chain and tensioner in position during assembly and disassembly on many VW & Audi vehicles. Compare to VW/Audi Factory Tool #3366 ...

Keeps the crankshaft pulley from turning when changing the timing belt and/or crankshaft seal Designed to withstand the torque specs for the crank...

Use to remove and install Fan Clutch Assemblies when replacing Water Pumps or doing other Engine Services Use two wrenches together: one for h...

Removes springs and valve guide seals without removing cylinder head. Used by removing rocker and fastening tool to stud with nut, then use an a...

Application: Tractors/Diesel Trucks Depth: 6" (150mm) Range: 60 - 175mm Features ratchet mechanism with square drive tools to a...

Use for turning the flywheel crank on Paccar engines Services 2011-2016 Kenworth and Peterbilt T880 models with Paccar MX, MX PMCI-2, MX-...

Tool is used for Compressing valve springs on the 3.0L without having to remove the head Applications: Fusion, Milan, MKZ, Escape, Mariner, Five H...

Designed for BMW cylinder head bolts 1/2" square drive bits are extra long (OAL 200mm) Allows access to reach down and remove stubborn cylinder he...

Removes stubborn pins from cylinder head 85mm OAL for access in tight areas where slide hammers wont fit Services Benz M102, M110, M115, M116, M11...

Counter-weighted design for high torque applications OAL: 89mm Use with 1/2" square drive tools Includes 3 metric sizes: 1064 - 17mm - Honda, ...

Removes valve stem seals from overhead camshaft engines Special designed long reach jaws (3-14/" / 80mm) access recessed valves on 4 valve per c...

Use with 3/4" drive tools to transmit high toque needed to losen and tighten head bolts Allows access to rear head bolts by eliminating t...

2 Pc. Set: 2450x03 - size: .001-.003" (green) 2450x04 - size: .002-.006" (red) Measures clearances of engine rod and main bearings without expe...

Use with the cylinder head still on the engine and in the car, or with the cylinder head removed Tool bolts to the head while the lever pivots fro...

Removes valve spring keepers and springs without removing the cylinder head Adjusts to fit springs on most cars Sliding "T" handle for close clear...

Designed to work in areas of difficult access using direct action compressor lever for better visibility Includes 2 valve spring adapter, fittin...

Removes and replaces valve keepers on all gas and diesel overhead valve engines, including motorcycle, marine and aircraft engines Tool is spring-...

Primes the lubricating system of new and rebuilt engines, sending oil to the internal moving parts before the first start Use with 3/8" o...

Primes the lubricating system of new and rebuilt engines, sending oil to the internal moving parts before the first start Use with 3/8" o...

Two part splined wrench is required for removal and replacement of free-wheel drive pulleys found on Bosch Alternators 10mm x 12 point end locks a...

17mm hex with 3/8” square drive. Fits all Gems engine Land Rovers, including: Range Rover Classic - ’87 – ’95 Range Rover 4.0/4.6 - ’95 – ’98 Dis...