Engine Service

Cam Phaser & Timing Chain Locking / Holding Set for 3.6L Pentastar engines Services 2016 and newer Chrysler, Dodge & Jeep models Compare t...

Use for locking the cams and crankshaft when replacing the timing chain and cylinder head gasket on the Porsche second gen V6 twin turbo engines A...

Use for easily removing stuck injectors Perfectly weighted slide hammer for injector extraction Services: Ford EcoBoost GDI engines (1.0L, 2.0L &a...

Removes and installs water pump pulley on Ford, Lincoln and Mercury 3.0L DOHC engines Includes: Forcing screw with shaft protector Pulley removal...

The crank position sensor (CPS) alignment block used for servicing the alignment of the Crank Sensor on many versions of the 2.0L & 2.3L Ford ...

For VVL (Variable Valve Lift) only, do not use on VVT (Variable Valve Timing) engines Services newer Dodge/Chrysler/Jeep models with Pent...

For use with #2865, 2867 & 2869 Camshaft Holders to lock the crankshaft at TDC Comparable to OEM #T40026 Application Details Make M...

Service head bolts on many VW & Audi models 1/2" square drive and 5-1/2" (14cm) long for deep-reach applications Ribe wrenches will also servi...

17mm by 12-point flare nut and deep crowfoot socket allows technician to remove hard-to-reach injector lines on Ford 6.7L Power Stroke application...

For removal & installation of 4/3-way central valve for camshaft adjustment Services 2.0L (4v) generation 1, 2 & 3 TFSI engine with chain ...

Used for adjusting the camshafts when performing service on the timing system Also found in CTA No. 7066 Volvo Camshaft Alignment Kit Compare to V...

Designed to fit the flex plate teeth Insert the tool into the flywheel housing until it engages the ring gear Use with a 1/2" square drive tool (r...

Counter-weighted design for high torque applications, including: Honda engines with 19mm hex pulley damper bolt. Toyota engines with 19mm hex ...

Removes and installs press-on type belt driven accessory pulleys on pumps with 3/8”-16 threaded shafts Interchangeable components allow service on...

The timing tool set includes the tools required to properly service GM Atlas/Vortec engine family Kit includes: 7459 - GM Lower Timing Gear Retai...

Comprehensive kit includes required components to perform complete timing service Services Porsche 911 Turbo & GT2 996 (1997-2006) & 997.1...

Tool kit is used to setup and service the engine timing on Porsche 4.8L V8, 3.0L Supercharged V6 & 3.6L V6 A properly working timing system al...

For removal and installation of the magnetic actuator Services B38 & B48 engine (1.5L & 2.0L) Compare to BMW Factory tool #2 0360 895 App...

Designed for locking the crankshaft and camshafts For correctly setting the timing position while servicing BMW B36, B38, B46 & B48 engines (1...

Splits and reconnects single & double row timing chains on Benz gas and diesel engines Also services some Saab & BMW vehicles Provides cle...

All the tools needed to service '09 & up models with turbo engines - TFSI Includes crank counter hold tool, crankshaft thrust piece, (4) drift...

Services 2006 - 2009 VW / Audi 2.0L Turbo engines Comparable to OEM #T10252 Application Details Make Model Trim Engine Year Audi A3 B...

Adjusts the tensioner on idler pulleys with pin holes Tool rotates pulley around the off-center retaining bolt for easy belt tension adjustment ...

Special bars lock camshafts relative to each other during timing belt and tensioner service or when removing crank bolts Use with CTA #2872 TDC ...

Installs piston rings from 27/8 to 43/8" (73-111mm) Includes ratcheting pliers and 6 sizes of 11/2" wide compressor bands Works either parallel or...

Use for timing service on BMW, MINI & Toyota (Supra) B38, B48 & B58 engine variants Locking camshafts and crankshaft, adjusting the camsha...

Specially designed to position the camshafts in TDC position Slackens and tightens the bolts attached to the camshaft gears Services: Mercedes-Ben...

Installer is designed to eliminate lip-flare on the wear sleeve, which can cause oil leaks during install Properly installs the seal, which helps ...

This comprehensive kit contains all the essential tools for servicing the crankshaft front and rear seals on Ford Powerstroke diesel engines Inclu...

For timing BMW N47, N47S 2.0L and N57 3.0L diesel engines Services: 1, 3, 5 Series, X3 from 2007-2015 Includes cam setting plate, flywheel pin, cr...

Use to install and remove the camshaft adjusters Use to secure cam position during timing chain replacement Made from durable Cr-V hardened alloy ...

Use to install and remove the camshaft adjusters  Use to secure cam position during timing chain replacement Made from durable Cr-V hardened alloy...

Use to install and remove the camshaft adjusters Use to secure cam position during timing chain replacement Made from durable Cr-V hardened alloy ...

Use to install and remove the camshaft adjusters Use to secure cam position during timing chain replacement Made from durable Cr-V hardened alloy ...

Master kit includes all timing tools required to set cams, valves & VANOS timing on BMW N51, N52, N53, N54 & N55 engines Incudes camshaft ...

Use to install the piston pin circlip on the 986 / 987.1 & 996 / 997.1 Found in P/N: 5018 - Porsche Cam Alignment Tool Kit & 7089 - Porsch...

Use for aligning the camshaft to TDC (Top Dead Center) Applications: 2014+ Mercedes Benz AMG C63, E63, S63, GT and GT-S with biturbo 4.0L V8 engin...

Puller component from #1094 Benz CDI Common Rail Injector Puller Kit U-Bracket design

Required to hold the flywheel in a secure position while servicing the balancer retaining bolt This tool allows for securing the flywheel by utili...

17mm Straight Socket

Alignment Bar Compare to Ford Factory Tool 303-376 Applications Make Model Engine Years Ford Fiesta 1.25L Duratec 2005-2013 Ford Fiesta 1....

19mm bushed socket to prevent slippage and rounding off of the cam bolt at the end of the camshafts Services 1980-1995 Porsche 911, 3.2L ...

For VVL (Variable Valve Lift) only, do not use on VVT (Variable Valve Timing) engines Services newer Dodge/Chrysler/Jeep models with Pentastar VVL...

Camshaft timing guides/blocks are used as fastening springs during assembly of camshaft drive pinions when in the timing position Servic...

Designed to position and hold the crankshaft when installing timing chains Applications: 1993-2004 Ford 4.2L 2 valve, 4.6L 4-valve, 5.4L V8, and 6...

Used for creating slack on the chain tensioner for replacing the timing chain without the need for removing the front cover Necessary for pushin...

Kit includes timing and seal service tools for services on the 1.6L Ecoboost engine. Components included in kit: #2822 - Ford Cam Locking Plate ...