Black Friday

Click here for application chart of clutch tool range Spline Diameter: 1 3/8" Metric Spline: 34.9250 Spline Count: 10 Pilot Diameter: .980 Metric ...

Holds torsion bar while making adjustments Services 2011 & up HD & C/K trucks (GM Trucks) Forged construction Bright blue body Click HERE...

Removes the Pivot Pins found on both tilt and telescopic steering columns Works on GM, Ford, and Chryslers with Saginaw steering columns

Hard-to-find bit-sockets to service "Figure 8" screws on old GM cars, trucks & some non-automotive applications Applications include headlight...

Remove and install door hinge spring GM Door Spring Compressor

A must for removing and installing serpentine belts with spring-loaded idler pulleys 23” long slender design provides proper reach and prevents ...

New Design with off-set Nitto fitting Internal Male Insert O.D. = 37mm I.D. 50.07mm Adapter O.D. = 66.5mm 3 Tab design For use with #7015 Bleeder...

Applications: GM / Chrysler Included in 11pc. Master Cylinder Adapter Kit - CTA Part # 7300 7" x 4 1/2" Rectangular Replacement Components: 7022X...

Removes and installs press-on type belt driven accessory pulleys on pumps with 3/8”-16 threaded shafts Interchangeable components allow service on...

Services the left & right head for "High Feature" 2006+ 2.8L, 3.0L & 3.6L V6 GM engines Prevents rotation during timing chain service Ind...

Scissor-Type Disconnect Tool Sizes: 5/16” 3/8” Service connectors found on GM, Ford, Mazda and Chrysler

Master kit for servicing the front and rear crankshaft seals on 2001-2016 6.6L Duramax diesel engines Includes: 3878 Rear Crankshaft Seal Install...

Holds flywheel in place when servicing the flywheel bolt and/or balancer Services Cadillac ATS, CTS, Chevy Malibu, Impala & Buick Regal Mount...

1.4L Ecotec (Turbo) Timing tool kit is used to set the timing For 2011 & up GM models with the 1.4L Ecotec engine Compare to GM Factory Tool: ...

Use to remove and install the snap-ring on the long reverse piston and return spring, without removing the center shaft and clutch assembly from t...

Designed for the L5P Diesel engine with two tank caps One cap is located on the side of the tank (Vented) with right-hand threads The other is loc...

Sizes: M0, M1, M2, M3, M4, all 3/8" square drive, all packed on socket rail Bits have asymmetrical geometry that provides enhanced installation of...

Used for installing a ball joint on a lower control arm Eliminates the need for an extra pair of hands Works with any 7/8” diameter p...

Holds torsion bar while making adjustments Services: '88 - '10 GMC Chevrolet 1/2 ton, 3/4 ton and 1 ton pickups S-10 Blazer S-15 Jimmy 4WD pickup...

Counter-weighted design for high torque applications Breaks loose crank bolts that regular sockets can't Services GM (LS engines) & Land Rover...

This rear crankshaft seal remover is designed to remove the rear seal on 2001 and newer 6.6L Duramax diesel engines. Its three jaws grab the inner...

This crankshaft seal and wear sleeve remover is designed for servicing the front crankshaft seal on 2001 and newer 6.6L Duramax diesel engines. Th...

"Flip" Socket offers 2 hex sizes in one socket - 22mm & 24mm Use with 1/2" drive extended shank impact tools with an extension Ser...

Applications: Ford F-series Heavy-Duty 3/4 & 1 ton Dana 50 IFS or Dana 60 front axle (1985-1995) Ford F-series 1/2 to...

Click here for application chart of clutch tool range Spline Diameter: 1" Metric Spline: 25.4000 Spline Count: 14 Pilot Diameter: .590 Metric Pilo...

Fuel Line Retaining Clip Tool Set Releases the nylon retaining clip. Includes 2 sizes: 3/8" and 5/16". Application: newer GMs and Chryslers wi...

Heavy Duty design Special bend to clear door panels Removes hinge pins on GM vehicles with removable hinge pins Includes Pin Puller to remove ...

Installs harmonic balancer or drive pulleys that are pressed on the camshaft Includes 12 adapters: M16-2.0 M16-1.5 M14-2.0 M14- 1.5 M12-1.75 M12-...

Test vehicles with Multi-port fuel injection Features 3-1/2" (90mm) gauge with dual calibration (5-145 PSI / 25-1,000 kPa) Hose with quick disconn...

Upgrades CTA #3300 with the following adapters: Hyundai, Kia, Mitsubishi Style - 11mm Fuel Rail Adapter, 15mm Fuel Rail Adapter, 16mm Fuel Rail A...

Applications: For injector testing on Navistar DT360, DT466, 9.0L, 312, 360, 414, 436 AND 446 C.I.D. Click 'Application Chart' for full ap...

Application: GM / Chrysler Used in conjunction with 7023 to close hole on 2-hole master cylinder Included in 11pc. Master Cylinder Adapter Kit - C...

Services elliptical-shaped fasteners now found on many vehicle applications Standard "Star" or Ribe designs will not fit these fasteners Black fin...

Applications: For glow plug on GM 6.2L V8 (10mm x 1.0) MADE IN USA

Services most steering wheels, including telescopic tilt columns Includes: 4 sets of cap screws 2 yokes Metric & SAE lock plate adapters and ...

Separate the hydrocarbon injection quick connect Offset design for improved access and easy use Services: 2010 & up diesel engines, includi...