Products

Tool kit is used to setup and service the engine timing on Porsche 4.8L V8, 3.0L Supercharged V6 & 3.6L V6 A properly working timing system al...

Used to setup and service engine timing for Porsche M96.03 3.6L H6 engine Services Porsche 986, 987, 996 & 997 generations Includes: Camsha...

7 Point socket for caliper retaining screws Applications: Audi Q7, S5 and various Mercedes Benz models 1/2" square drive OAL: 50mm Applications ...

7 Point socket for caliper retaining screws on Audi S4 & S5 models 1/2" square drive Length 48mm Applications Make Model Year Audi ...

10 Point socket for caliper retaining screws on Porsche Cayenne & Audi Q7 models 3/8" square drive OD: 11.5mm Length 50mm Application Details...

10 Point socket for caliper retaining screws on Porsche Macan, Cayenne, Audi Q7 & S8 models Visit ctatools.com for application details 3/8" sq...

10 Point socket for caliper retaining screws 1/2" square drive OD: 20mm Length 50mm Applications Make Model ...

Services the caliper retaining screws on VW/Audi/Porsche (VAG) brakes Includes sizes: 5025 - 7pt. x 14mm - 1/2" Sq. Dr. 5027 - 7pt. x 22mm - 1/2"...

The Cummins ISB Front Crankshaft Seal Remover & Installer for ISB Paccar PX-6 is designed for both removing and installation of the crankshaft...

Properly setup and service engine timing Tool locks the timing chains against the hydraulic tensioners to prevent tensioner ratcheting and pisto...

Installs Factory front seal #3937111, #3904353 and the seal found in kit #3802820 Note: CTA #5046 is required if the seal has a wear sleeve Appli...

Tool is used for Compressing valve springs on the 3.0L without having to remove the head Applications: Fusion, Milan, MKZ, Escape, Mariner, Five H...

Tool is used for holding the Crankshaft Damper on 2005-2011 Ford 2.0L, 2.3L & 2.5L engines Applications: Fusion, Focus, Transit, Milan, MKZ, E...

Designed to fit the slotted adjusting screw in tapered kingpins Application: Most Mack front axles (12,000 to 20,000 lbs.) Use with a ...

6 spread pins for an exact fit for Dodge applications Applications: Dodge RAM 1500-4500 models Wheel hub assemblies usually go bad when the wheel...

Tool is used for installing the front Crankshaft Wear Sleeve Note: CTA #5041 is required for installing factory seal #3937111, #3904353 and the se...

Tool holds the camshaft at T.D.C. to ensure proper timing when performing service on timing system components (cams, gears, chains, etc.) Designed...

Applications: Mack E7 and Cat 3208 Dimensions: 8 Splines x 1.725”(43.815mm) Compare to Factory Tool #0508477 1/2" Square Drive Application Detail...

Designed to position and hold the crankshaft when installing timing chains Applications: 1993-2004 Ford 4.2L 2 valve, 4.6L 4-valve, 5.4L V8, and 6...

Kit includes both the Camshaft (7640X01) and Crankshaft (5050) holding brackets Designed to position and hold the camshaft and crankshaft on 1993-...

Designed to turn irregularly shaped parts The double action head allows use in either direction Ratcheting action also makes it possible to re-gr...

Designed to turn any irregularly shaped parts The double action head allows use in either direction Ratcheting action also makes it possible to r...

Tool mounts to the front of the block, its tabs engage both cam phasers to be held in place so the phaser bolts may be serviced The ECOTEC engines...

For easy access to 10mm hex fasteners found on Hose Clamps and other applications 6" long flexible shaft for working in limited clearance ...

This Drive Shaft/CV Axle Puller/Wheel Bearing Hub Installer Kit is designed for pulling drive shafts into hubs Makes installing new CV shafts easi...

Ultra stubby design for limited clearance applications OAL: 20mm 12mm hex drive on each Hex bit Sizes: H3, H4, H5, H6, H7, H8 & H10 Packed in ...

3mm Hex bit 12mm Hex Drive w/ Ball Lock Found in set 5057

4mm Hex bit 12mm Hex Drive w/ Ball Lock Found in set 5057

5mm Hex bit 12mm Hex Drive w/ Ball Lock Found in set 5057

6mm Hex bit 12mm Hex Drive w/ Ball Lock Found in set 5057

7mm Hex bit 12mm Hex Drive w/ Ball Lock Found in set 5057

8mm Hex bit 12mm Hex Drive w/ Ball Lock Found in set 5057

10mm Hex bit 12mm Hex Drive w/ Ball Lock Found in set 5057

Ultra stubby design for limited clearance applications OAL: 20mm 12mm hex drive on each "Star" bit Sizes: T10, T15, T20, T25, T27, T30, T40, T45 &...