Products

Spread: 6" (152mm) Reach: 3-1/2" (89mm) Screw Length: 7" (178mm) Capacity: 5 tons (4.5MT) Instructions Hook the jaws to the desired gear, compone...

Spread: 7" (178mm) Reach: 5-1/2" (140mm) Screw Length: 7" (178mm) Capacity: 5 tons (4.5MT) Instructions Hook the jaws to the desired gear, compon...

Spread: 9" (229mm) Reach: 5-1/2" (140mm) Screw Length: 9" (229mm) Capacity: 7 tons (6.4MT) Instructions Hook the jaws to the desired gear, compon...

Spread: 10" (254mm) 25cm Reach: 9" (229mm) 23cm Screw Length: 9" (229mm) 23cm Capacity: 7 tons (6.4MT) 6364 Kg Instructions Hook the jaws to the ...

Spread: 12" (305mm) 30cm Reach: 11" (279mm) 28cm Screw Length: 13" (330mm) 33cm Capacity: 13 tons (11.8MT) 11820 Kg Instructions Hook the jaws to...

Spread: 4" (102mm) Reach: 3-1/2" (89mm) Screw Length: 5" (127mm) Capacity: 2 tons (1.8MT) Thread size: 9/16" (14mm) 20 Threads per inch Instructi...

Spread: 7" (178mm) Reach: 3-1/2" (89mm) Screw Length: 7" (178mm) Capacity: 5 tons (4.5MT) Thread size: 9/16" (14mm) 20 Threads per inch Instructi...

Spread: 8" (203mm) Reach: 5-1/2" (140mm) Screw Length: 7" (178mm) Capacity: 5 tons (4.5MT) Thread size: 9/16" (14mm) 20 Threads per inch Instruct...

Spread: 10" (254mm) Reach: 5-1/2" (140mm) Screw Length: 9" (229mm) Capacity: 7 tons (6.4MT) Thread size: 9/16" (14mm) 20 Threads per inch Instruc...

Spread: 11" (279mm) 28cm Reach: 9" (229mm) 23cm Screw Length: 9" (229mm) 23cm Capacity: 7 tons (6.4MT) 6364 Kg Instructions Hook the jaws to the ...

Spread: 14" (356mm) Reach: 11" (279mm) Screw Length: 13" (330mm) Capacity: 13 tons (11.8MT) Instructions Hook the jaws to the desired gear, compo...

Spread: 17" (432mm) Reach: 15" (381mm) Screw Length: 13" (330mm) Capacity: 13 tons (11.8MT) Instructions Hook the jaws to the desired gear, compo...

Remove generator gears, bearings, bearing cones and similar parts where ordinary puller jaws will not reach Knife-like edges minimize damage to pa...

Used to remove the roof grab handle of various VW models Without causing damage to clips or headliner Compare to VW Factory Tools #T10517, T10518 ...

Makes removing rubber exhaust hangers easy Slim profile with a self locating pin and 25° offset allow for easy access in confined areas ...

Used for creating slack on the chain tensioner for replacing the timing chain without the need for removing the front cover Necessary for pushin...

Remove generator gears, bearings, bearing cones and similar parts where ordinary puller jaws will not reach Knife-like edges minimize damage to pa...

Removes and installs water pump pulley on Ford, Lincoln and Mercury 3.0L DOHC engines Includes: Forcing screw with shaft protector Pulley removal...

Removes fly wheel pilot bearings and bushings up to 7-1/2" (190mm) long Better than slide hammer type when working in tight areas Better control f...

For inside pulling jobs, jaws will remove flywheel pilot and other bearings Range: 1/2" to 1-1/2" (13mm to 38mm) Replacement Jaws: 8070x06 - Stan...

Similar to #8075 but extra long 20-1/2" (521mm) for added reach Range: 1/2" to 2" (13mm to 50mm) Instructions Outside Pulling: Using the nuts an...

Removes pressed-on 1 or 2 groove pulleys from alternators and power steering pumps without damage Fits both large and small pulleys found on old...

Complete set of tools to remove and install press-on-type belt-drive Bosch and Denso Alternator Pulleys Components include: Torx ®, Triple-Square...

Removes and installs press-on type belt driven accessory pulleys on pumps with 3/8”-16 threaded shafts Interchangeable components allow service on...

Two part splined wrench is required for removal and replacement of free-wheel drive pulleys found on Bosch Alternators 10mm x 12 point end locks a...

Services free-wheel pulleys found on VW, Audi, Volvo, Mercedes Benz, Porsche, etc. with Bosch Alternators Features two-part design - 33 spline end...

Sets & adjusts timing on '98 - '07 VW TDi engines Engine: 1.9L & 2.0L TDi Includes: Lock Pins Cam Lock Bar ...

Using this special cable, record the noise from a wireless electric stethoscope on any smartphone while listening live on a Wireless Electronic St...

Pull parts with two tapped holes, including gears, fan pulleys, balancers, and cam gears Cross-arm is 1" (25mm) square and 5" (127mm) long, with 5...

Remove parts with tapped holes with 81/4" (210mm) yoke and 115/8" (300mm) long forcing screw Puller spreads from 2" to 7 3/4" (50mm to 200mm)

For use with CTA and other brands of Bearing Splitters when removing and installing Gears, Bearings, Shafts, Pulleys and other press-fit parts Cap...

Use for turning or adjusting various types of fasteners that have holes or notches on their outer surface Includes 4 pairs of interchangeable 2-si...

Replacement pins for 8120 Pin Spanner Set Size: 2.5mm / 4mm

Replacement pins for 8120 Pin Spanner Set Size: 3.5mm / 5mm

Replacement pins for 8120 Pin Spanner Set Size: 6mm / 8mm