Products

9 liter (10 quart) tank unit dispenses fluid under pressure for fast, safe and clean refilling of transmission fluid or ATF reservoirs on most mak...

Use with CTA #7400 Services Infiniti vehicles with 8 x 1.0 threaded end Special threaded end services Nissan/Infiniti 7 Speed Will work on most "N...

Use with CTA #7400 Services: VW-DSG & Audi- S Tronic Automatic Transmissions Will work on all standard ATF filling Tanks Applications: Audi A...

Services GM vehicles with 6L50, 6L80, 6L90, 8L45, 8L90, 10L60, 10L80 & 10L90 Transmissions Use with CTA 7400 Tank, will work on most "Non-CTA"...

Full range of extra low-profile oil filter housing cap sockets Extra low-profile sockets for tight clearances Applications: For use on all vehicle...

Keeps the lower timing gear locked while the cylinder head is removed from engine Services I4, I5 & I6 (Atlas) engines Without this tool, the ...

19mm bushed socket to prevent slippage and rounding off of the cam bolt at the end of the camshafts Services 1980-1995 Porsche 911, 3.2L ...

The Oil Funnel Stand is designed to keep your work area clean and organized Its 2-in-1 purpose design is for storage and collection of re...

Includes #7471 funnel plus #7473 & 7485 to service most European vehicles VW/Audi (VAG)- 1.8L, 1.9L TDI, 2.0T, 2.8L, 3.0L, 3.2L, 3.6L, 4.2L V...

Slotted Double-D Socket 6 x 8mm

Holds camshaft sprockets on 2005 & Up Subaru Models with 2.5L Turbo and 3.6L 6-cylinder engines Diameter - 31.7mm x 28mm x 7mm OAL: 47.5 cm Co...

Includes camshaft holding fixtures & chain tensioner hold down pin Services: Ford EcoBoost V6 engines Engine: 2.7L, 3.5L & 3.7L V6 Compon...

Removes fuel injector found on BMW N20 & N55 engines Comparable to BMW Factory Tool #130 320 7658 is found in our more comprehensive 7644 kit ...

1.2mm Female Terminal (3 Pack)

Use for easily removing stuck injectors Perfectly weighted slide hammer for injector extraction Services: Ford EcoBoost GDI engines (1.0L, 2.0L &a...

Replacement Guide M8X100 for 7802 Glow Plug Tip Puller Kit

Plug Puller Adapter

Hex Nut

Electrode Puller Screw

Slide Hammer Counter Weight

Slide Hammer Bar

For the removal & installation of the front lower control arm bush(ing) Can be used in situations without removing the arm from the vehicle Wh...

Used for removing and installing the fuel tank/Fuel pump retaining ring Use on many Late 90’s and early 00’s Volvo models Compare to Volvo Factory...

2-piece bit-in-socket design for maximum torque strength Size: 5mm OAL: 2.20” (56mm) 1/2" square drive MADE IN USA Applications: Brake C...

Locks camshafts and crankshaft in position when servicing the timing chain and setting engine timing A properly working timing system allows the e...

Master kit includes all timing tools required to set cams, valves & VANOS timing on BMW N51, N52, N53, N54 & N55 engines Incudes camshaft ...

Jaw Spread: 15" (381mm) 38cm Jaw Reach: 15" (381mm) 38cm Center Screw Length: 13" (330mm) 33cm Center Screw Diameter: 11/16" Center Screw TPI: 16 ...

Used for creating slack on the chain tensioner for replacing the timing chain without the need for removing the front cover Necessary for pushin...

Remove bearings, gears, bushings, seals, grease retainers, etc. Includes 4 jaw assemblies for internal/external and 2/3 jaw pulling 3 jaw range: 1...

Mortorq Socket Size: "4" 3/8" square drive Also available in a set of 5 - CTA Part # 8140

Spindle rethread die for heavy duty trucks Use for rethreading wheel lug nut studs 32mm Hex Most common H.D. Truck Size

Type: NC (Coarse) Size: 3/4", 7/8" - 9, 1" - 8, 1-1/8" - 7, 1-1/4" - 7 5 Pc. NC-USS Die Set Packed in Square Plastic Sliding Case MADE IN ...

Stubby 12-Point Triple Square "XZN" Used for tight access applications Application Guide: #8511 - Various applications on European vehicles. #8...

Installer Washer (Q) 59mm OD For Kit 8650 or 8650M

Installer Washer (L) 73mm OD For Kit 8650 or 8650M

Installer Washer (M) 71.3mm OD For Kit 8650 or 8650M