Products

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to remove wh...

Separates the steering knuckle & suspension joints from control arms and strut assemblies using an impact hammer Can also be used to remove wh...

9 liter (10 quart) tank unit dispenses fluid under pressure for fast, safe and clean refilling of transmission fluid or ATF reservoirs on most mak...

Use with CTA #7400 Thread size: M10 x 1.0  Will work on most "Non-CTA" ATF Filling System Tanks For use on VW/Audi Sport Differential (Haldex) Ap...

Use with CTA #7400 ATF Filling Adapter Services Mercedes vehicles with 722.9 12 x 1.5 threaded end Will work on most "Non-CTA" ATF Filling System ...

Use with CTA #7400 Services VW & Audi vehicles with DSG 24 x 1.5 threaded end Will work on most "Non-CTA" ATF Filling System Tanks Compare to ...

Use with CTA #7400 Services Toyota, Lexus vehicles with 18 x 1.5 threaded end Special cabled 15cm / 6" hose helps regulate ATF temperature Will wo...

Use with CTA #7400 Services Infiniti vehicles with 8 x 1.0 threaded end Special threaded end services Nissan/Infiniti 7 Speed Will work on most "N...

Use with CTA #7400 Services: VW-DSG & Audi- S Tronic Automatic Transmissions Will work on all standard ATF filling Tanks Applications: Audi A...

Go-Thru Deep Socket - 22mm

Includes camshaft holding fixtures & chain tensioner hold down pin Services: Ford EcoBoost V6 engines Engine: 2.7L, 3.5L & 3.7L V6 Compon...

Used for aligning the front crankshaft seal on BMW N55 engines Use in conjunction with CTA 7643 components Compare to BMW factory tool #119235 Ap...

The 7658U BMW Fuel Injector Tool Kit with 24mm Wrench features the 7658 BMW Fuel Injector Remover Tool designed specifically for N20 and N55 engine...

3.0mm Male Terminal (3 Pack)

2.5mm Female Terminal (3 Pack)

0.7mm Female Terminal (3 Pack)

Services the left & right head for 2006+ 3.0L & 3.6L V6 & 2004+ 2.8L I4, 3.5L I5 & 4.2L I6 GM Atlas engines Prevents rotation duri...

Plug Puller Adapter

Extractor Screws

Slide Hammer Counter Weight

Slide Hammer Bar

Thread Repair Tap M10 x 100

Includes components found in kit #7880 If you have discontinued kit #4080, purchase #7880X10 to upgrade your kit

2-piece bit-in-socket design for maximum torque strength Size: 5mm OAL: 2.20” (56mm) 1/2" square drive MADE IN USA Applications: Brake C...

Ignition coil puller removal tool prevent coil damage caused by home-made removal methods and prevent injury to hand in tight quarters. Comfort T-...

Ignition coil puller removal tool prevent coil damage caused by home-made removal methods and prevent injury to hand in tight quarters. Comfort T-...

Spread: 7" (178mm) Reach: 5-1/2" (140mm) Screw Length: 7" (178mm) Capacity: 5 tons (4.5MT) Instructions Hook the jaws to the desired gear, compon...

Designed for installation of front and rear crankshaft seals and wear sleeves on Cummins diesel engines Precision-machined installers ensure corre...

Replacement pins for 8120 Pin Spanner Set Size: 2.5mm / 4mm

Replacement pins for 8120 Pin Spanner Set Size: 3.5mm / 5mm

Mortorq Socket Size: "4" 3/8" square drive Also available in a set of 5 - CTA Part # 8140

• Designed to keep sensors connected during diagnostics, maintaining signal integrity• Allows direct measurement from connector to connector for si...

The CTA 8488 Brake-Pro Electric Pressure Brake Bleeder (holds up to 60L tank) features a user-friendly fully digital LCD screen and touch panel. O...

Use for precise removal and installation without removing the subframe from the vehicle Ideal for maintaining proper alignment, ride quality, and ...

6 Point Hex drivers for a variety of applications Long flex cable shaft allows access in tight areas to service hose clamps and other fast...

Master kit services Rear Wheel Hubs & Bearings on European vehicles, plus Front Wheel Hubs & Bearings on US, Asian & European vehicles...