Products

Makes removing rubber exhaust hangers easy Slim profile with a self locating pin and 25° offset allow for easy access in confined areas ...

Remove generator gears, bearings, bearing cones and similar parts where ordinary puller jaws will not reach Knife-like edges minimize damage to pa...

Removes fly wheel pilot bearings and bushings up to 7-1/2" (190mm) long Better than slide hammer type when working in tight areas Better control f...

For inside pulling jobs, jaws will remove flywheel pilot and other bearings Range: 1/2" to 1-1/2" (13mm to 38mm) Replacement Jaws: 8070x06 - Stan...

Similar to #8075 but extra long 20-1/2" (521mm) for added reach Range: 1/2" to 2" (13mm to 50mm) Instructions Outside Pulling: Using the nuts an...

Removes pressed-on 1 or 2 groove pulleys from alternators and power steering pumps without damage Fits both large and small pulleys found on old...

Complete set of tools to remove and install press-on-type belt-drive Bosch and Denso Alternator Pulleys Components include: Torx ®, Triple-Square...

Remove bearings, gears, bushings, seals, grease retainers, etc. Includes 4 jaw assemblies for internal/external and 2/3 jaw pulling 3 jaw range: 1...

Pull parts with two tapped holes, including gears, fan pulleys, balancers, and cam gears Cross-arm is 1" (25mm) square and 5" (127mm) long, with 5...

Remove parts with tapped holes with 81/4" (210mm) yoke and 115/8" (300mm) long forcing screw Puller spreads from 2" to 7 3/4" (50mm to 200mm)

For use with CTA and other brands of Bearing Splitters when removing and installing Gears, Bearings, Shafts, Pulleys and other press-fit parts Cap...

Use for turning or adjusting various types of fasteners that have holes or notches on their outer surface Includes 4 pairs of interchangeable 2-si...

Remove generator gears, bearings, bearing cones and similar parts where ordinary puller jaws will not reach Knife-like edges minimize damage to pa...

Remove generator gears, bearings, bearing cones and similar parts where ordinary puller jaws will not reach Services Heavy Duty applications Knife...

Restores damaged threads on bolts and shafts Files are cross-cut and depth proportional to the thread pitch, so will not skip or jump out of fine ...

Restores damaged threads on bolts and shafts Files are cross-cut and depth proportional to the thread pitch, so will not skip or jump out of fine ...

Restores damaged threads on bolts and shafts Files are cross-cut and depth proportional to the thread pitch, so will not skip or jump out of fine ...

Includes thread file #8231 and #8233 plus the following Taps and Dies: Tap & Die Sets: Metric - 6 x 1.00, 8 x 1.50, 10 x 1.00, 10 x 1.25, 1...

Includes 6 Metric Dies: 20 - 1.25, 20 - 1.50, 22 - 1.00, 22 - 1.50, 24 - 1.50, 24 - 2.00mm and 2 Fractional Dies: 3/4" - 20 & 13/16" - 20 ...

Type: NC (Coarse) Size: 3/4", 7/8" - 9, 1" - 8, 1-1/8" - 7, 1-1/4" - 7 5 Pc. NC-USS Die Set Packed in Square Plastic Sliding Case MADE IN ...

Type: NF (Fine) Size: 3/4", 7/8" - 14, 1" - 14, 1-1/8" - 12, 1-1/4" - 12 5 Pc. NF-SAE Die Set Packed in Square Plastic Sliding Case MADE IN USA

For use on 420, 428, 520, and 530 chains First bolt locks chain in place while second bolt turns to drive pin completely through the link Foldi...

For use in tight spaces 3.5" (90mm) long hardened jaws Adjust from 1.2" - 3.5" (30mm - 90mm) Thin Jaw Bearing Remover

4" / 102mm long for deep-reach applications 2-piece construction for high torque applications 3/8" drive Size: 5mm MADE IN USA

4" / 102mm long for deep-reach applications 2-piece construction for high torque applications 3/8" drive Size: 6mm MADE IN USA

4" / 102mm long for deep-reach applications 2-piece construction for high torque applications 3/8" drive Size: 7mm MADE IN USA

4" / 102mm long for deep-reach applications 2-piece construction for high torque applications 1/2" drive Size: 8mm MADE IN USA

4" / 102mm long for deep-reach applications 2-piece construction for high torque applications 1/2" drive Size: 10mm MADE IN USA Applications: cyl...

4" / 102mm long for deep-reach applications 2-piece construction for high torque applications 1/2" drive Size: 12mm MADE IN USA

4" / 102mm long for deep-reach applications 2-piece construction for high torque applications 1/2" drive Size: 14mm MADE IN USA

7 Pc. Super-Stubby 12-Point XZN Dual-Drive Bit Set 19mm long sockets with combination 1/4" square drive & 1/2" hex drive to work in the tighte...

Fits hydraulic cylinders on vehicles with gland nuts from 1" to 3-3/4" / 25mm to 95mm Reverses to work on 1/4" or 7/32" pinholes Use with 1/2" squ...

Fits hydraulic cylinders on vehicles with gland nuts from 2" to 6" / 51mm to 152mm (pin to pin) Reverses to work on 17/64" or 21/64" pinholes U...

6 Point Hex drivers for a variety of applications Long flex cable shaft allows access in tight areas to service hose clamps and other fast...

Master kit services Rear Wheel Hubs & Bearings on European vehicles, plus Front Wheel Hubs & Bearings on US, Asian & European vehicles...

Master kit services Rear Wheel Hubs & Bearings on European vehicles, plus Front Wheel Hubs & Bearings on US, Asian & European vehicles...